This page is about SkullSpace's 3D printer, a MendelMax 2.0.

MendelMax 2.0 Specs

Print Area Dimensions: 245 mm x 315 mm x 225 mm
Print Area: 17,364.8 cm3
Printer Dimensions: 450 mm x 340 mm x 460 mm
Usable Maximum Print Speed: 250mm/sec or more depending on the part, print material, and extruder
Usable Maximum Movement Speed: 500+ mm/sec
Layer Height: .1-.4mm, user selectable. Lower layer heights are also possible.
X & Y Axis Resolution: .0125mm
Frame: All aluminum
Movement: linear rail (X and Y axis), precision shafting and bushing (Z axis)
Heated Bed: 24V 200W Heated Bed included
Power Requirements: 110-220 VAC
Hotend: J-Head Mk V-BV 0.4 mm / 3.0 mm

How to print

Currently it is still being built/calibrated/tuned and cannot be used to print anything yet.

Todo

Tuning (see below)
Install heatsinks on pololus (Andrew has ordered these)
Install/mount fans on heatsinks on pololus (Andrew has ordered these)
Install Z end stop hall effect sensor (needs 3d printed part)
Install X/Y end stops (needs 3d printed parts)
Swap out car pads with tighter tolerance ones
Install power switch
Cover up 120v exposures
- Cover for power supply terminals
- Grounded box for ac plug
Replace some temp plastic clips with zip ties
Print/acquire cable chain for carriage wiring and X motor wiring
Set up dedicated Raspberry Pi with pronterface and VNC for printing and toss it on the network
Nice big "don't touch you will get burned" / etc sing should be printed and displayed
UPS of some kind for long print jobs
Webcam for monitoring print status

Tuning

Extruder hotend and bed thermistors were both verified to be working properly
Z axis was raised to prevent grinding and leveled
Extruder
- Discovered high print speed causes abs to accumulate in the gear threads which causes slippage
- 300 mm/min seems to be a bit too fast
- 220c & 100mm/min seems to be working best for abs so far
- Remember to set diameter of filament in pronterface
Bed needs to be leveled

Things we need to print

Z end stop hall effect sensor mount
X end stop mount
Y end stop mount
carriage fan mount
cable chains

Flashing new firmware

Currently we have the MendelMax 2.0 no end stop firmware running on it. It uses an Arduino clone called the Taurino that is similar to a Arduino Mega 2560.

The flashing procedure is to load up the Arduino software and configure it as for an Arduino Mega 2560, compile and flash. It did not work on linux but worked worked fine on Windows with the Taurino drivers installed.

Software

We have tested it with Pronterface, and it seems to work well. It should be set to 250000 baud rate. 250k baud doesn't seem to work with linux very well so we may switch it to 115200 or soemthing lower:

https://github.com/ErikZalm/Marlin/issues/205

The stock MendelMax firmware has the extruder running backwards so the plug shoud be flipped (ie blue wire away from the power connector).

Eventually we would like to set up a Raspberry Pi running pronterface that is on the network and can be VNC'd into to control the printer or set up print jobs. Some good links that show how to do this are here:

https://github.com/gklyne/things/wiki/Setting-up-a-Raspberry-Pi-as-RepRap-host-controller

http://entropyprojects.blogspot.ca/2012/07/reprap-printing-from-raspberry-pi.html

http://entropyprojects.blogspot.ca/2012/08/slic3r-on-raspberry-pi.html

Historical Records

On January 23, 2013, Ron emailed announce@ to solicit donations for the printer. So far, we've had pledges of (the numbers are for my (Ron's) reference):

$200 (1)
$100 (2)
$100 (3)
$100 (4)
$100 (5)
$300 (6)
$100 (7)
$50 (8)
$100 (9)
$50 (10)
$50 (11)
$60 (12)
$50 (13)
$100 (14)
$50 (15)

For a total of $1460 of our $1600 goal!

Proposal

Hey everybody,

Ben Bergman knows somebody who's selling a 3d printer. He has pictures and stuff that he can post later, but for now, the important info is:

- It's worth about $1500 new, it's being sold for $1000 - There are 7 spools of plastic refills for $50 each (retail price is $65)

So basically, if we can raise $1350, we can buy SkullSpace a 3d printer! This is an all-or-nothing thing, so please email me off-list and tell me what you're willing to contribute (I'll personally put in $100). A few others at the Awesome Foundation meeting last night offered to put in, as well, so please let me know who you were.

If we manage to get enough donations to make the $1350, we'll go forward with this. Then plan would be to leave it set up at the space, and maybe take it with us to special events if it's mobile enough (I don't know much about this stuff, obviously). It would be free for anybody to use, but we'd ask for donations for material (like the drink machine fund).

Here's Ben's proposal, from the Awesome Foundation site (reprinted with implied oral permission, not express written permission): -- I would like to purchase a 3D printer to use in my open hardware projects. Open hardware is where all the design files for recreating some physical object are fully published and available to anyone that wants to recreate it with whatever changes they want. To facsilitate the spreading of the open hardware movement and the utility of 3D printing, I would like to bring this 3D printer with me to public events where people can try it for themselves and see what is possible with this up-and-coming technology. The ability to quickly create a prototype object greatly improves the ability to bring an interesting project to fruition.

When not is use at events, the 3D printer would be located at SkullSpace, Winnipeg's hackerspace, to grant easy access for others interested in 3D printing and open hardware. SkullSpace has open events multiple times per week which would make a good time for non-members interested in these things to drop by and try things out.

There are other organizations that have 3D printers available, but their memberships can be prohibitively expensive for hobbyists or people trying to start small side businesses. Easier access to one of these tools will aide in the creation of more great devices and local businesses. --

Printer details: Mendel Max 2.0

$1490 + plastic filament (possibly from the used printer bundle)

$60 less if we do border pickup

Suggested funding goal: $1600-$1700 to cover some plastic filament or duty/tax, if there is any

The Mendel Max 2.0 is my primary recommendation, if we can get one. Here's why. http://www.mendelmax.com/

Pros:

Print Area Dimensions: 245 mm x 315 mm x 225 mm (9.6"x12.4"x8.9")
Usable Maximum Print Speed: 250mm/sec or more depending on the part, print material, and extruder
Frame: All aluminum

http://www.mendelmax.com/?wiki=mendelmax-versions

Cons:

Currently in beta (any parts changed after beta are included in beta price, just need to pay shipping)
Won't ship until February 25

Availability:

$1490.00 as a kit

http://store.makerstoolworks.com/printer-kits/mendelmax-2-0-beta-kit/

It prints 100mm/sec faster and has a larger print envelope than both the Ultimaker and the Mendel Max 1.5. It is also closely related to the open source Reprap project and community.

3d printer

Contents

MendelMax 2.0 Specs

How to print

Todo

Tuning

Things we need to print

Flashing new firmware

Software

Historical Records

Proposal

Printer details: Mendel Max 2.0

Archive

Original option: Used (local and working) Thing-O-Matic

Navigation menu

Personal tools

Namespaces

Variants

Views

More

Search

Navigation

Tools